Copley Controls Serial Encoder Guía de usuario Pagina 138
- Pagina / 157
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Xenus Plus User Guide Thermal Considerations
Copley Controls 138
C.3: Heatsink Mounting Instructions (XE2/XP2/800-
1782/800-1808)
description
The XE2-HK is a kit containing a heatsink and mounting hardware for field installation of a
standard heatsink onto Xenus Plus XE2 model servo drive. To order an XE2 drive with heatsink
fitted at the factory, add “-H” to the model part number.
installation
1) Place the heatsink fins-down on a work surface.
Orient the heatsink so that the edge with part
number is away from you. The hole for the XE2
grounding lug should be to your left.
2) Remove the clear protective film from the thermal
material and discard it. Place the thermal material
onto the heatsink in the placement area which is
marked with four white “L”.
Apply light pressure to ensure that the thermal
material is flat.
3) Peel the white protective layer away from the
thermal material. Do this slowly from one corner
so as not to lift the thermal material from the
heatsink.
4) Align the XE2 as shown and lower onto the
heatsink.
If needed to adjust the position, lift it away from
the thermal material and lower onto the heatsink
again.
5) Install the four mounting screws with flat washers
and tighten evenly. Torque to 17.8 lb-in (2.0 Nm)
maximum.
Note: If alignment markings
are not on heatsink, use
these dimensions to place
the pad
(1) Thermal material (TM)
(2) Mounting position of TM
(3) Heatsink
- Xenus Plus 1
- User Guide 1
- Xenus Plus User Guide 2
- This page for notes 2
- Copley Controls 3 3
- Copley Controls 4 4
- ABOUT THIS MANUAL 5
- Original Instructions 6
- Related Documentation 7
- Comments 7
- Copyrights 7
- Document Validity 7
- Product Warnings 8
- Copley Controls 9 9
- CHAPTER 10
- Copley Controls 11 11
- 1.2: CME 2 12
- 1.3: CML/CMO 13
- 1.5: Indexer 2 13
- 1.6: CPL 13
- 2.1: Drive Internal Power 15
- Copley Controls 16 16
- 2.3: Commutation Modes 17
- 2.4: Feedback 17
- 2.5: Operating Modes 18
- Copley Controls 19 19
- Limiter 19
- Description 19
- Copley Controls 20 20
- Copley Controls 21 21
- Commanded Velocity 22
- Limited Velocity 22
- Vel Limit 22
- Accel Limit Decel Limit 22
- Copley Controls 24 24
- 2.6: Input Command Types 25
- Copley Controls 26 26
- 2.6.2: PWM Input 27
- Pulse Input 28
- Velocity 28
- Direction Input 28
- Up Input 29
- Command 29
- Down Input 29
- 2.7: Communication 30
- Copley Controls 31 31
- Copley Controls 32 32
- Addressing Method 32
- -1 -2 -3 33
- 2.8: Limit Switches 34
- 2.9: Brake Operation 35
- 2.10: Status Indicators 36
- Copley Controls 38 38
- Color/Blink Code 38
- Meaning 38
- STAT-Drive Status 40
- NET-MACRO Network Status 40
- XPL J6 STAT Indicator 42
- 1 second 43
- 2.11: Protection 47
- Copley Controls 48 48
- Fault Description 48
- Fault Occurs When… 48
- Fault is Corrected When… 48
- Copley Controls 49 49
- Copley Controls 50 50
- Copley Controls 51 51
- 2.13: Inputs XEL/XPL/XML 53
- 2.14.1: Digital Inputs 54
- 2.14.2: Analog Inputs 54
- 2.15: Outputs, XEL/XPL/XML 55
- Copley Controls 56 56
- 2.17: Regen Resistor Theory 57
- 3.1: Agency Approvals 59
- 3.2: Power Input 59
- 3.3: Power Output 60
- 3.4: Control Loops 61
- 3.5: Regen Circuit Output 61
- 3.6: Digital Command Input 61
- 3.7: Analog Inputs 62
- 3.8: Digital Inputs 63
- 3.9: Analog Outputs 64
- 3.10: Digital Outputs 64
- 3.12: Primary Encoder Inputs 65
- 3.13: Analog Encoder Inputs 66
- 3.14: Hall Switch Inputs 67
- 3.15: Resolver Interface 68
- 3.16: Multi-Mode Port 69
- 800-1782 70
- 3.17: Serial Interface 71
- 3.18: Network Interfaces 72
- 3.19: Status Indicators 73
- 3.20: Fault Levels 73
- 3.21: Power Dissipation 74
- 3.22: Thermal Impedance 74
- XEL/XPL/XML 75
- XE2/XP2/800-1782/800-1808 75
- 3.24: Dimensions 76
- Copley Controls 77 77
- 3.24.3: XML Dimensions 78
- Copley Controls 80 80
- Copley Controls 81 81
- 4.1.3: Connector Locations 82
- 1782/800-1808 83
- Copley Controls 84 84
- Copley Controls 85 85
- 4.3: Motor(s) 86
- 4.4.1: XEL/XPL/XML 87
- 4.5: Logic Supply / Brake 89
- Mating Connector 90
- 4.6: Safe Torque Off 91
- Copley Controls 92 92
- Copley Controls 94 94
- 1 2 3 4 5 6 95
- 4.8: Network Ports 96
- 4.8.2: CAN Bus (XPL/XP2) 97
- Copley Controls 98 98
- 4.9: Control I/O 99
- Copley Controls 101 101
- Analog Input Wiring Diagram 102
- Analog Output Wiring Diagram 102
- 4.10: Secondary I/O 103
- Copley Controls 104 104
- Copley Controls 105 105
- Mating Connections 106
- Pin Description 106
- 800-1782 Pin Description 111
- Copley Controls 112 112
- Copley Controls 113 113
- 4.11: Motor Feedback 115
- Pin Description 800-1782 117
- Hall Switch Wiring Diagram 119
- Copley Controls 120 120
- Resolver Wiring Diagram 121
- APPENDIX 124
- Capacity 127
- A.1.11: Select Fuses 128
- T Algorithm 130
- B.1.3: I 131
- T current limit 132
- Ambient Temperature ( 134
- 4.25 in 135
- Configurations 136
- 1782/800-1808) 138
- D.1: Overview 140
- D.3: Thermal Considerations 141
- Copley Controls 142 142
- Copley Controls 143 143
- D.5.2: Connector Locations 144
- D.5.3: Cable Notes 145
- Copley Controls 148 148
- F.1: Drive Model Numbers 150
- 800-1808 152
- F.2: Accessory Model Numbers 153
- F.3: Heatsink Kits 154
- F.5: Edge Filter 155
- F.6: Order Example 155
- F.7.1: Specifications 156
- F.7.2: Dimensions 156
Ch-technology VSKV91.. Series manuels
Manuels d'utilisation et guides de l'utilisateur pour Matériel Ch-technology VSKV91.. Series.
Nous fournissons des manuels en pdf 1 Ch-technology VSKV91.. Series à télécharger gratuitement par type de document : Manuel de l'utilisateur
Ch technology VSKV91.. Series Manuel de l'utilisateur (11 pages)
marque: Ch-technology | Catégorie: Hardware | Taille: 0.43 MB |
Table des matières
Plus de produits et de manuels pour Matériel Ch-technology
| Modèles | Type de document |
|---|---|
| CHASSR125 |
Manuel de l'utilisateur
C&H Technology CHASSR125 User Manual,
4 pages
|
| SD853C..S50K Series |
Manuel de l'utilisateur
C&H Technology SD853C..S50K Series User Manual,
9 pages
|
| PS21997-4A |
Manuel de l'utilisateur
C&H Technology PS21997-4A User Manual,
8 pages
|
| VSK.F200..P Series |
Manuel de l'utilisateur
C&H Technology VSK.F200..P Series User Manual,
9 pages
|
| ME501606 |
Manuel de l'utilisateur
C&H Technology ME501606 User Manual,
5 pages
|
| VSKDS203-100 |
Manuel de l'utilisateur
C&H Technology VSKDS203-100 User Manual,
10 pages
|
| SR |
Manuel de l'utilisateur
C&H Technology SR User Manual,
3 pages
|
| PM150CL1B060 |
Manuel de l'utilisateur
C&H Technology PM150CL1B060 User Manual,
6 pages
|
| Phawo...k.. |
Manuel de l'utilisateur
C&H Technology Phawo...k.. User Manual,
4 pages
|
| VS-GA75TP60S |
Manuel de l'utilisateur
C&H Technology VS-GA75TP60S User Manual,
7 pages
|
| PM150CVA060 |
Manuel de l'utilisateur
C&H Technology PM150CVA060 User Manual,
7 pages
|
| CM600HU-12H |
Manuel de l'utilisateur
C&H Technology CM600HU-12H User Manual,
5 pages
|
| VSHPS1480 |
Manuel de l'utilisateur
C&H Technology VSHPS1480 User Manual,
5 pages
|
| PM30RSF060 |
Manuel de l'utilisateur
C&H Technology PM30RSF060 User Manual,
9 pages
|
| QR_0630T30 |
Manuel de l'utilisateur
C&H Technology QR_0630T30 User Manual,
4 pages
|
| ST173CPBF Series |
Manuel de l'utilisateur
C&H Technology ST173CPBF Series User Manual,
9 pages
|
| VS38ESR..M Series |
Manuel de l'utilisateur
C&H Technology VS38ESR..M Series User Manual,
2 pages
|
| CPCF-High-Volume |
Manuel de l'utilisateur
C&H Technology CPCF-High-Volume User Manual,
3 pages
|
| SPR2214 |
Manuel de l'utilisateur
C&H Technology SPR2214 User Manual [en] ,
3 pages
|
| PM50CL1B060 |
Manuel de l'utilisateur
C&H Technology PM50CL1B060 User Manual,
6 pages
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales